In most cases I would first try the replacement mentioned above. This would customarily be a double pole switch with two layers of wires attaching. Our website is also a rich resource for information you won't find in your basic fan manual. More about Ceiling Fan Switch Wiring How to Install Ceiling Fans Take the mystery out of ceiling fan wiring. Forget reaching up to the pull chains: Use the wall control to turn your ceiling fan on and off.
Replace either type of switch following the same procedure. Remove the Capacitor There are two ways to remove the capacitor. Make careful note of which wires attach where to the pullchain. Some fans have a switch that only turns the fan on or off, while others have a switch that powers the fan at three different speeds. A ceiling fan reversing module controls the direction of the fan blades.
Am I missing something here? Ceiling Fans are a great way to lower your energy bill and brighten up one of your favorite rooms. If for whatever reason you do not know which wires connect to which locations on the pullchain, you may yet have some options. I thought I would disconnect all the other wires and then connect the light's brown to my L on the pull switch and red to No. The lighting works without a problem, now I have a dead fan. Harsch received her Certified Nurses Assistant license in 2004. This goes for the unit as well as the electrical power in your room. I cannot stress this step enough.
This is usually achieved either by removing two screws on the bottom cap of the switch housing, or three screws on the side. In addition to posting comments on articles and videos, you can also send your comments and questions to us on our or at 800 946-4420. Open the switch housing of the fan. What is causing this to happen? Referencing the image above, unscrew the brass tip, detach the wires, and remove the old switch from the housing. You choose to operate the blades at high, medium or low speed, or stop the blades from spinning by pulling the chain attached to the side of the fan. Get the most out of your Hunter ceiling fan with a working manual and access to all of the replacement and upgrade parts you need.
Estimated Time: Depends on personal level experience and ability to work with tools. He is a certified Master Naturalist, regularly monitors stream water quality and is the editor of freshare. Can I use it anyway? The order in which the wires are attached as well as the colors of attached wires are important. Hold the wire to keep it in the switch while you pull the paperclips from the opening. I've exhausted trying to fix this fan. If your ceiling fan has a light kit, you will need to remove the kit before opening the bottom part of the switch housing. The pullchain is used to turn the fan off and on, and in some cases also to reverse the fan, select between the high speed and the various low speeds derived from the speed control, or also control the light.
Repeat the step to install the remaining three wires. Your ceiling fan has a broken light pull chain. However in most fans the wires are inserted directly into the pullchain. Board, wall switch, pull chain switch, reversing switch, hanger bracket, capacitor, flywheel, light bulbs, switch housing covers, reversing module, light limiter and many other ceiling fan parts. This is a single pole triple throw switch with an off position. Be Careful and Be Safe - Never Work on Energized Circuits! A pull chain activates a switch inside the fan assembly.
In order for me to assist you I would need to know more about your pull chain switch wiring diagram and the wires that are found on your ceiling fan, the make and model of the ceiling fan would be helpful as well. There are some exceptions such as certain model Fasco fans. This should be a simple process and is often secured by tightening screws that loop through the blades and into the motor. When the chain breaks inside the fan housing, it is typically broken inside the switch. Materials: Make sure the replacement pull chain switch has the same as the original switch, and is fully compatible with the ceiling fan you have. Time to Assemble the Fan Now, it is time to assemble your ceiling fan unit. I had access to the pull switch and could see the broken chain inside it.
Also, the light switch itself may wear out or fail. If you already have your fan installed, you'll still find helpful information through our support page. In most cases the important relationships are between L and the various other positions, for example a three speed four wire switch might be L-1-2+3-3. We aim to make it easy for our customers to find ceiling fan repair parts and replacement parts to get their fans up and running again. This article has also been viewed 258,590 times.
I am certain I have the new switch wired the same as the old one as I cut off and restripped the wires so the wires were still on the old switch. If the fan does not work with the likely replacement, does not work on all speeds, spins too fast, too slow, etc. That will aid you in attaching the wires correctly when installing the new switch. At that point, you simply replace the 3-Speed Fan Switch rather than trying to fix the chain. How do you fix this fast and easy? Every fan is different and if you do not make note there will likely be a complicated guessing game. These are the switches that your local hardware store should stock.
How do I replace a ceiling fan pullchain? Take a look at the to find buying guides when you need a new fan and online ordering information so you can track your shipment after ordering. Good luck Anonymous : I have a 3 speed, 4 wire ceiling fan. Electrical Tip The Safest Way to Test Electrical Devices and Identify Electric Wiring! It is only used on fans that are operated by a remote control. Online Resources Getting a copy of your Hunter fan manual through our website can help you with installation, adding accessories like light kids, and finding replacement parts for your fan. How can we be sure? They are furnished with wire leads to further speed installation.